modelSprayInjectorVLE_L3_advanced
Extends from ClaRa.Basics.Icons.SprayInjector, ClaRa.Basics.Icons.ComplexityLevel (Displays the complexity level inside model icon ).
Information
For detailed model documentation please consult the html-documentation shipped with ClaRa.
Authorship and Copyright Statement for original (initial) Contribution
Author:
DYNCAP/DYNSTART development team, Copyright © 2011-2024.References:
For references please consult the html-documentation shipped with ClaRa.
Remarks:
This component was developed by ClaRa development team under the 3-clause BSD License.
Acknowledgements:ClaRa originated from the collaborative research projects DYNCAP and DYNSTART. Both research projects were supported by the German Federal Ministry for Economic Affairs and Energy (FKZ 03ET2009 and FKZ 03ET7060).
CLA:
The author(s) have agreed to ClaRa CLA, version 1.0. See https://claralib.com/pdf/CLA.pdf
By agreeing to ClaRa CLA, version 1.0 the author has granted the ClaRa development team a permanent right to use and modify his initial contribution as well as to publish it or its modified versions under the 3-clause BSD License.
The ClaRa development team consists of the following partners:
TLK-Thermo GmbH (Braunschweig, Germany)
XRG Simulation GmbH (Hamburg, Germany).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| Modelica.Units.SI.SpecificEnthalpy | h_start_main | 3000e3 | |Initialisation|Fluid|Initial specific enthalpy of main phase |
| Modelica.Units.SI.SpecificEnthalpy | h_start_spray | h_start_main - 100 | |Initialisation|Fluid|Initial specific enthalpy of spray phase |
| Modelica.Units.SI.Pressure | p_start | 1e5 | |Initialisation|Fluid|Start value of sytsem pressure |
| Real | y_start | 0.05 | |Initialisation|Fluid|Start value for ratio spray volume to total volume |
| Modelica.Units.SI.Temperature[N_wall] | T_wall_start | ones(N_wall)*TILMedia.VLEFluid.MixtureCompatible.Functions.temperature_phxi(medium, p_start, h_start_main) | |Initialisation|Wall|Start values of wall temperature |
| Boolean | useHomotopy | simCenter.useHomotopy | |Initialisation||True, if homotopy method is used during initialisation |
| Boolean | checkValve | false | |Expert Settings|Injector Valve|True, if spray injector valve is check valve |
| Boolean | useStabilisedMassFlow | false | |Expert Settings|Injector Valve|True, if use pseudo state for mass flow in spray injector valve |
| Real | Tau | 0.001 | |Expert Settings|Injector Valve|Time constant of pseudo state in spray injector valve |
| Real | opening_leak_ | 0 | |Expert Settings|Injector Valve|Leakage valve opening in p.u. |
| Integer | N_wall | 3 | |Expert Settings|Wall|Number of radial elements of the wall |
| Basics.Units.Time | Tau_cond | 0.03 | |Expert Settings|Mixing Model|Time constant of condensation |
| Basics.Units.Time | Tau_evap | Tau_cond | |Expert Settings|Mixing Model|Time constant of evaporation |
| Basics.Units.CoefficientOfHeatTransfer | alpha_ph | 50000 | |Expert Settings|Mixing Model|HTC of the phase border |
| Basics.Units.Area | A_phaseBorder | 10 | |Expert Settings|Mixing Model|Heat transfer area at phase border |
| Real | exp_HT_phases | 0 | |Expert Settings|Mixing Model|Exponent for volume dependency on inter phase HT |
| Basics.Units.VolumeFraction[2] | eps_mix | {0.2, 0.8} | |Expert Settings|Mixing Model|Volume fraction V_1/V_tot of min/max mixed outlet |
| Boolean | showExpertSummary | simCenter.showExpertSummary | |Summary and Visualisation||True, if expert summary should be applied |
| Boolean | showData | false | |Summary and Visualisation||True, if a data port containing p,T,h,s,m_flow shall be shown, else false |
| Fundamental Definitions | |||
| TILMedia.VLEFluid.Types.BaseVLEFluid | medium | simCenter.fluid1 | Medium in the component |
| Geometry | |||
| Modelica.Units.SI.Length | diameter_o | 0.5 | Diameter of the component |
| Modelica.Units.SI.Length | diameter_i | 0.45 | Diameter of the component |
| Modelica.Units.SI.Length | length | 3 | Length of the component |
| Nominal Values | |||
| Modelica.Units.SI.Pressure | p_nom | 1e5 | Nominal pressure |
| Modelica.Units.SI.MassFlowRate | m_flow_nom_main | 10 | Nominal mass flow rates at inlet |
| Initialisation › Fluid | |||
| Integer | initOptionFluid | 211 | Type of initialisation of fluid |
| Initialisation | |||
| Integer | initOptionWall | 213 | |Initialisation|Wall|Initialisation option of wall |
Connectors
| Type | Name | Default | Description |
|---|---|---|---|
| ClaRa.Basics.Interfaces.FluidPortIn | inlet1 | Inlet port | |
| ClaRa.Basics.Interfaces.FluidPortIn | inlet2 | Inlet port | |
| ClaRa.Basics.Interfaces.FluidPortOut | outlet | Outlet port | |
| Modelica.Blocks.Interfaces.RealInput | opening | =1: completely open, =0: completely closed | |
| ClaRa.Basics.Interfaces.EyeOut | eye |
Components
| Type | Name | Default | Description |
|---|---|---|---|
| String | complexity (from ComplexityLevel) | "??" | |
| ClaRa.SimCenter | simCenter | ||
| Summary | summary | ||
| Basics.ControlVolumes.FluidVolumes.VolumeVLE_L3_TwoZonesNPort | mixingZone | ||
| ClaRa.Basics.ControlVolumes.SolidVolumes.CylindricalThickWall_L4 | wall | ||
| ClaRa.Components.VolumesValvesFittings.Valves.GenericValveVLE_L1 | valve |
Contents
| Name | Description |
|---|---|
 Outline | |
 Wall_L4 | |
 Summary | |
 Material | |
 PressureLoss | |
 HeatTransfer | |
| PressureLoss_mixingZone |
Revisions
For revisions please consult the html-documentation shipped with ClaRa.